Menu

Category: Fiberglass

Loading...
green-cocoon-insulationvt-moldy-fiberglass2

Don’t Make These Basement Insulation Mistakes

Insulation Tips

Incorrectly installed basement insulation is a common error. We see this problem not only with do-it-yourself installation, but also with contractor installation. The results can be disastrous as severe mold and mildew may become a problem, not to mention the loss of money on your heating bill. This is why we beg you, “don’t make these basement insulation mistakes.”

Use Treated Lumber

Since most basements are inherently moist, you need to keep all untreated wood away from the concrete surfaces. Moisture below the slab can wick up into the concrete and get to the base plates of the wall. Therefore, you need to make certain the bottom plate of the wall is treated lumber.

Avoid Using Fiberglass Insulation in Basements

As seen in the photo above, putting polyethylene over fiberglass insulation is a no-no as it doesn’t allow the insulation to breathe. Consequently, this homeowner had moisture build-up and ultimately mold growth!

For years contractors have been treating basements much like regular living space. It’s not uncommon to see fiberglass insulation in direct contact with basement foundation walls. Here in the northeast, we see several common mistakes, including:

  • Plastic vapor barrier against concrete wall, fiberglass insulation inside stud wall, then drywall
  • Fiberglass insulation inside a “bag” hanging from the rim joist down along the foundation wall
  • Stud wall filled with fiberglass insulation an inch or two away from the concrete wall[1]

Those mistakes can increase the chances for mold to grow.

What Causes Mold to Grow in Basements?

Mold can grow on virtually any organic material as long as it has the right moisture level and oxygen. Because mold eats or digests what it is growing on, it can damage a building and its furnishings. If left unchecked, mold eventually can cause structural damage to building materials and can cause health problems. That’s why we don’t want mold in our basements! Specifically, we can prevent damage to buildings and building contents in the basement areas, save money, and avoid these potential health problems by controlling moisture.

green-cocoon-insulationvt-moldy-fiberglass

According to the EPA, indoor relative humidity in homes should be kept below 60 percent — ideally between 30 and 50 percent. [2] In addition to preventing mold formation, maintaining the correct humidity levels may also have a bonus effect. It may discourage pests such as cockroaches, silverfish (bristletails), and dust mites from showing up where you don’t want them!

To measure the humidity of your home or basement, you need to buy a humidity meter and track the relative humidity level. That is the first part of understanding the mold problem in your home or basement.

Education Needed

If contractors are still using fiberglass insulation in basements, it means that we in the industry need to do a better job educating our builders. In order to understand the issues with basement insulation, you first must understand the role of vapor barriers in basements.

Use the Right Insulation

Over the years, we’ve come to rely on two main approaches for basement insulation projects and remodeling, including closed cell spray foam and rigid foam board. When installed in the correct thickness, these two methods result in a proper vapor barrier and superior insulation.

Get Educated – Be the Pro!

Today, the building industry and building science are changing rapidly. In order to stand out in the competition and provide a professional service to your clients, you need to stay educated on the latest methods. You can be sure that the team at The Green Cocoon is up-to-date on the latest insulation practices in order to bring our clients the best product possible.

If you have questions or need a quote on your next insulation project, contact us and we’d be happy to help.

[1] Be the Pro. Avoiding Basement Insulation Mistakes. Retrieved from bethepro.com.

[2] United States Environmental Protection Agency. Mold Course Chapter 2. Retrieved from epa.gov.

green-cocoon-r-value, photo courtesy of bpihomeowner.org

Did You Know? Insulation R-Value Changes

Insulation Tips

In the world of building construction, improvement, and insulation, we talk about R-value all the time. Usually, we talk about it as if it’s a constant number. We see R-19 stamped right there on the product, so that’s what it is, right? Well, did you know that the insulation R-value changes?

What Is R-Value?

R-value is a measure of resistance to heat flow through a given thickness of material. Furthermore, it is important, but it’s just one of a few key factors that determines the effectiveness of an insulation material. R-value is tested in an air-tight vacuum chamber, which means that typical insulation materials like fiberglass and cellulose do not actually perform with that value unless paired with intense air sealing measures.

green-cocoon-closed-cell-r-value-chart[1]

How Is R-value measured?

Because of scams involving R-value claims that didn’t match reality, the U.S. Federal Trade Commission (FTC) devised the R-value Rule to protect buyers of insulating products. In fact, in 2013 the FTC handed down its largest fine ever ($350,000) to a company claiming that its paint had an R-value of 100.[2]

So, the R-value Rule requires testing insulation using one of four American Society of Test Methods (ASTM) standards. The basic requirement is that the mean temperature must be 75° F (24° C) with a temperature difference of 50° F (28° C) across the insulation.[3]

According to Building Science Corporation, most R-value testing is done with a temperature of 50° F (10° C) on the cold side and 100° F (38° C) on the hot side.[4]

The Lowdown on R-value

The main point here is that R-value isn’t some constant number for a given material, and installation isn’t the only factor that affects it. As you can see above, temperature has a significant effect as well.

The team at The Green Cocoon knows that the performance of the insulation is affected by how well it is installed. Energystar.gov has developed guidelines for grading the quality of installation. Moreover, they’ve developed a table that shows what levels of insulation are cost-effective for different climates and locations in the home.[5]

Compression

Improperly installed insulation loses its R-value. For example, fiberglass can lose up to 50 percent of its prescribed R-value when compressed. Additionally, when you compress fiberglass batt insulation, the R-value per inch goes up, but the overall R-value goes down because you have less inches or thickness of insulation.[6]

Fear not, closed cell spray foam is the only insulation material that has an almost constant R-value. The reason is because you cannot pass air through it or compress it.

Contact us to find out more about R-value or for a free quote.

[1] Building Performance Institute (April 4, 2017). What Does R-Value Mean? Retrieved from bpihomeowner.org.

[2] FTC.gov (January 31, 2013). FTC Action Leads to Court Order: Home Insulation Marketer to Pay $350,000. Retrieved from ftc.gov.

[3] Electronic Code of Federal Regulations (March 31, 2020). R-value Rule. Retrieved from ecfr.gov.

[4] Building Science Corporation (April 12, 2013). Info-502: Temperature Dependence of R-values in Polyisocyanurate Roof Insulation. Retrieved from buildingscience.com.

[5] Energy.gov. Recommend Home Insulation R-Values. Retrieved from energy.gov.

[6] Insulation Institute. The Facts About Compressing Fiber Glass Insulation. Retrieved from insulationinstitute.org.

Solar Panels in a Field - Green Cocoon Insulation

New Report on Environmental Impacts of Spray Polyurethane Foam

Insulation Tips

The Spray Polyurethane Foam Alliance (SPFA) recently published a Life Cycle Assessment (LCA) Use Phase Analysis report. The report evaluates the environmental impacts and performance of spray polyurethane foam (SPF) insulation. It compares the environmental impacts of spray foam insulation as compared to fiberglass insulation, specifically measuring cumulative energy demand and global warming potential for homes insulated in different US climate zones.

Three Homes Tested

Three homes were equally insulated according to 2018 IECC requirements in their respective climate zones using fiberglass as a baseline and various types of spray polyurethane foam insulation. What was  the conclusion?

SPF Insulation Can Reduce Carbon Emissions

After reading the report, our biggest surprise was how SPF insulation can reduce carbon emissions! “The report shows the reduction in carbon emissions by using SPF insulation instead of fiberglass in a single home is the equivalent of removing 14 to 23 automobiles from the road for an entire year.”

Read the entire article at sprayfoam.com.

Questions? Contact us and we’d be happy to answer them!

iSprayfoam.com (March 23, 2021) – SPFA Releases Report on Environmental Impacts of SPF

a pile of fiberglass insulation from a clients home

Why We Say, “Don’t Use Fiberglass Insulation!”

Insulation Tips

We recently got a call from a homeowner who wanted their attic insulation replaced. Their old fiberglass insulation was wet and dirty and needed to be replaced. Not only that, it had originally been installed upside down, leading to moisture problems.  We weren’t surprised by this situation as we get calls for help all the time. Our advice is to do it right the first time. That's why we say, "Don’t use fiberglass insulation!!

In cold climates fiberglass just won’t do

Fiberglass insulation is significantly cheaper than spray foam insulation, but it is also less effective, especially in extremely warm conditions. Summers in New England regularly hit above 100°F. Spray foam is more expensive, but you get your money back within five years.[1]

Used in roughly 85% of American homes, fiberglass insulation is the most common form of home insulation. Spray foam insulation has less market share, but is increasing in popularity.[2]  Why? Because it is MUCH better and you pay once. Professional installation is required for spray foam insulation, but hey, would you have the plumber fix your broken tooth?

Energy efficiency of fiberglass vs. spray foam

The composition of fiberglass insulation does not stop air from passing through it. On average, more than 30% of heat or air conditioning escapes where fiberglass insulation is installed. If poorly installed, fiberglass can also leave spaces around fixtures, allowing even more heating or cooling to escape.

Spray foam insulation fills all spaces, preventing air from escaping. It acts as an air barrier. Spray foam insulation is significantly more efficient than fiberglass and has a higher R-value.[3]

Problems with fiberglass

Incorrect installation – Failing to fill the wall cavities and compressing the batts are two of the most prevalent installation mistakes. They’re also the leading causes of poor performance, which is why some green building consultants, architects, and builders recommend other products. Their answer for total fill: cellulose.[4]

In a recent project we repaired, the insulation was originally installed incorrectly. As a matter of fact, because it was installed incorrectly, the vapor barrier (the brown paper side) couldn’t do its job – to trap moisture against the floor. The raft paper has to be facing the conditioned space, in this case the attic floor.

It’s cheap – That means that many home builders can offer it to reduce the cost of the home. But don’t be fooled. You may pay less now, but you’ll pay more later, for sure.

Rodents love it! – Rodents prefer safe, warm, and sheltered environments – making the inside of your walls and attic the ideal home. Insulation that can be found in these places can be even more inviting since it is a source of warmth for the scurrying critters. The malleability of fiberglass insulation makes it easy for a nest to be made, and insulation can be moved where ever needed. Once one nest is established and a rodent is comfortable enough, a colony of rodents can soon follow. With the displacement of materials, you could see a difference in the heating as warm air can now escape from your house in those areas.[5]

Length of life

Fiberglass insulation can last several years, but during that time it loses its effectiveness and you never have a complete seal against air flow. The level of effectiveness also depends if any moisture is present. You may need to replace this type of insulation or add to it as it settles and deteriorates over time.

Spray foam, on the other hand, can last as long as 80 years or more. It’s a much more permanent and effective option. While you’ll pay more up front, the longevity and efficiency of spray foam make it a very cost-effective option. [6]

In closing, when it comes to which is best in the spray foam insulation vs. fiberglass debate, spray foam wins, hands down. If you’re a DIYer, you may be used to installing fiberglass insulation. But if you’re looking for something that will last a lifetime, let a professional install spray foam. [7]

[1] The Green Cocoon (2019). Invest in Insulation. Retrieved from thegreencocoon.com.
[2] Diffen (2019). Fiberglass Insulation vs. Spray Foam Insulation. Retrieved from diffen.com.
[3] Diffen, Fiberglass
[4] Probuilder (2015). Home Insulation Choices: Fiberglass, Cellulose, or Foam? Retrieved from probuilder.com.
[5] Apple Pest Control (2017). Rodents and Your Insulation. Retrieved from applepestcontrol.com.
[6] Good Life Energy Savers (2018). Spray Foam Insulation vs Fiberglass: What’s the Difference? Retrieved from goodlifeenergysavers.com.
[7] Good Life Energy Savers. Spray Foam

Home Builders Sacrifice Energy Efficiency by Using Cheap Insulation

Insulation Tips
CSIRO ScienceImage 2175 Installing Insulation Batts

This is a great article about why over half the new homes in the USA are insulated with fiberglass batts.

"The big problem with fiberglass is that nobody understands how to properly install it to minimize air leakage. And if they do understand how to install it, they don't want to spend the time and money doing it.

"So builders will happily keep building crappy walls that the wind can blow through because people can’t see it. They would rather sell visible performance, like windows and mechanical systems, because they can get real money for that."

Read entire article from Treehugger.com, and then call us!

Photo of how insulation helps in the summer

Insulation Is Important Year-Round

Insulation Tips

Insulation isn't just for the winter months! Heating and cooling account for 50 to 70% of the energy used in the average American home. Inadequate insulation and air leakage are leading causes of energy waste in most homes. In the summer, insulation keeps the walls, ceilings and floors of your home cooler, which eases the load on your air conditioner and lowers your cooling costs.

Ask us about insulating your home today! Give us a call at (978) 462-0082

Recent Posts
Categories